My Account
My Shopping Cart
Share this page
Fluoro Inverter - Electronic Ballast - 12 Volt - 40 Watt
12 Volt, 40 Watt "Fluoro Inverter"
This fluoro inverter (also known as electronic ballast) allows the use of 240V fluorescent tubes in a 12 Volt DC power system. Slim design for retrofitting in existing fluoro battens.
Suitable for T8 Tubes (diameter about 25mm) - not suitable for T5 (thin tubes).
The T5 is the newest technology and is more expensive than the T8 in many applications. The 5 number indicates the diameter of the bulb in eighths of an inch. So, a T8 is 8/8 inches in diameter, or 1 inch, and the T5 is 5/8 inch.
Has also been used successfully to run 32 Watt circular fluoro.
Features:
- Sinewave - high efficiency with low current drain
- Protection against reverse polarity connection
- Connection to both input and output via screw terminals located on PCB
- Compact and lightweight aluminium heatsink construction
- Pre-punched slots at either end of heatsink for ease of installation
Specs:
- Fluorescent tube rating: 30-40W
- Operating voltage: 9-15V DC
- Full load current 2A
- Dimensions (mm): 150(L) x 40(W) x 30 (H)
Installation:
1. Disconnect the battery supply before contact with any component of the Inverter
2. Ensure that the wire used for connecting the inverter has an insulation rating of minimum 240 volt
3. When wiring, use an in-line fuse holder with a fuse (5A for 12V and 2A for 24V) and place in the positive line
4. Ensure that the two (2) filaments (one either end) on the tube are connected to the module connectors as marked (i.e. F1 and F2)
5. Check that polarity is not reversed (positive to negative etc) and that correct input voltage is applied
6. Mount in a well ventilated area
7. Locate the inverter as close as possible to fluoro tube
Note: We recommend the use of fibre washers with locating screws (if screws are being used) when securing module. If metal washers are used, ensure they (or any other metal surface e.g. screwdriver) DO NOT touch transistors. If transistors are shorted, damage to the module may result which void warranty.
Weight: 0.17 Kilograms
Warranty: 2 yrs
Code: INV-140
Price: $50.00 Fluoro Inverter - Electronic Ballast - 12 Volt - 40 Watt Fluoro Inverter 12V 40W 2000mA
This fluoro inverter (also known as electronic ballast) allows the use of 240V fluorescent tubes in a 12 Volt DC power system. Slim design for retrofitting in existing fluoro battens.
Suitable for T8 Tubes (diameter about 25mm) - not suitable for T5 (thin tubes).
The T5 is the newest technology and is more expensive than the T8 in many applications. The 5 number indicates the diameter of the bulb in eighths of an inch. So, a T8 is 8/8 inches in diameter, or 1 inch, and the T5 is 5/8 inch.
Has also been used successfully to run 32 Watt circular fluoro.
Features:
- Sinewave - high efficiency with low current drain
- Protection against reverse polarity connection
- Connection to both input and output via screw terminals located on PCB
- Compact and lightweight aluminium heatsink construction
- Pre-punched slots at either end of heatsink for ease of installation
Specs:
- Fluorescent tube rating: 30-40W
- Operating voltage: 9-15V DC
- Full load current 2A
- Dimensions (mm): 150(L) x 40(W) x 30 (H)
Installation:
1. Disconnect the battery supply before contact with any component of the Inverter
2. Ensure that the wire used for connecting the inverter has an insulation rating of minimum 240 volt
3. When wiring, use an in-line fuse holder with a fuse (5A for 12V and 2A for 24V) and place in the positive line
4. Ensure that the two (2) filaments (one either end) on the tube are connected to the module connectors as marked (i.e. F1 and F2)
5. Check that polarity is not reversed (positive to negative etc) and that correct input voltage is applied
6. Mount in a well ventilated area
7. Locate the inverter as close as possible to fluoro tube
Note: We recommend the use of fibre washers with locating screws (if screws are being used) when securing module. If metal washers are used, ensure they (or any other metal surface e.g. screwdriver) DO NOT touch transistors. If transistors are shorted, damage to the module may result which void warranty.
Weight: 0.17 Kilograms
Warranty: 2 yrs
Code: INV-140
Price: $50.00 Fluoro Inverter - Electronic Ballast - 12 Volt - 40 Watt Fluoro Inverter 12V 40W 2000mA
No downloads for this product.
Close
QLD:
Gold Coast (from Coolangatta to Southport), Nerang and Hinterland (Beaudesert) and out West (Warwick, Stanthorpe, Killarney)
NSW:
Northern NSW (Tweed Heads to Yamba, including Evans Head, Byron Bay and Ballina); the Far North Coast Hinterland (Grafton via Lismore to Murwillumbah) and out West (Casino to Tenterfield, including Drake and Tabulam, as well as Woodenbong and Bonalbo)
For larger system we also go up to Brisbane or down to Coffs Harbour and even Glen Innes. Other places by arrangement.
We install solar systems in Northern NSW and Southern QLD.
QLD:
Gold Coast (from Coolangatta to Southport), Nerang and Hinterland (Beaudesert) and out West (Warwick, Stanthorpe, Killarney)
NSW:
Northern NSW (Tweed Heads to Yamba, including Evans Head, Byron Bay and Ballina); the Far North Coast Hinterland (Grafton via Lismore to Murwillumbah) and out West (Casino to Tenterfield, including Drake and Tabulam, as well as Woodenbong and Bonalbo)
For larger system we also go up to Brisbane or down to Coffs Harbour and even Glen Innes. Other places by arrangement.